2020.11.30 PDF HLD-BNWAS600 GNV-GL型式认可证书 文件下载.pdf

Certificate No: MEDB00003R1 Application of: Directive 2014/90/EU of 23 July 2014 on marine equipment (MED). This Certificate is issued by DNV GL SE based on the notification of the Federal Maritime and Hydrographic Agency of Germany. This is to certify: That the Bridge Navigational Watch Alarm System (BNWAS) ND ER with type designation(s) HLD-BNWAS600 Issued to Beijing Highlander Digital Technology Co., Ltd. Beijing, PR China LA is found to comply with the requirements in the following Regulations/Standards: Regulation (EU) 2017/306, item No. MED/4.57. SOLAS 74 as amended, Regulations V/18 & V/19, IMO Res. A.694(17), IMO Res. MSC.128(75), IMO Res. MSC.191(79), IMO Res. MSC.302(87), IMO MSC.1/Circ.1474 Further details of the equipment and conditions for certification are given overleaf. This Certificate is valid until 2023-06-06.   GH Issued at Hamburg on 2018-06-07 for DNV GL SE Digitally Signed By: Mydlak-Röder, Christine DNV GL local station: Tianjin HI Approval Engineer: Harald Bluhm Location: DNV GL Hamburg, Germany on behalf of Notified Body No.: 0098 Sven Dudszus Head of Notified Body The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer’s Declaration of Conformity issued when the production-surveillance module (D, E or F) of Annex B of the MED is fully complied with and controlled by a written inspection agreement with a Notified Body. The product liability rests with the manufacturer or his representative in accordance with Directive 2014/90/EU. This certificate is valid for equipment, which is conform to the approved type. The manufacturer shall inform DNV GL SE of any changes to the approved equipment. This certificate remains valid unless suspended, withdrawn, recalled or cancelled. Should the specified regulations or standards be amended during the validity of this certificate, the product is to be re-approved before being placed on board a vessel to which the amended regulations or standards apply. Form code: MED 201.DEU Revision: 2016-12 www.dnvgl.com Page 1 of 2 © DNV GL 2014. DNV GL and the Horizon Graphic are trademarks of DNV GL AS. Job Id: 344.1-007800-1 Certificate No: MEDB00003R1 Product description The Beijing Highlander Bridge Navigational Watch Alarm System (BNWAS), type HLD-BNWAS 600 consists of the following equipment: HLD-OPU600 1. Operation Unit Software version: 1.xx 2. Interface Unit Software version: 1.xx 3. Alarm Unit 4. Reset Unit 5. Waterproof Reset Unit HLD-ALU600 HLD-REU601 HLD-REU602 Options: 1. Motion Detection Unit 2. Visual Alarm Unit 3. Battery Unit HLD-MDU600 HLD-VAU600 HLD-BAU600 ND ER HLD-INU600 Documentation: HLD-BNWAS 600 Operation Manual Version 1.xx and HLD-BNWAS 600 Installation Manual Version 1.xx LA Type Examination documentation Testreport: HLD9600CG (IEC62616, IEC62288, IEC61162series) Testreport: SITIIAS A12-064-ZC (IEC60945) GH Tests carried out IEC 60945 (2002) incl. IEC 60945 Corr. 1 (2008) IEC 61162-1 ed4.0 (2010-11) and ed5.0 (2016-08) IEC 62288 Ed. 2.0 (2014-07) IEC 62616(2010) incl. IEC 62616 Corr. 1 (2012) HI Marking of product According to Article 10 of the Council Directive (MED): • The wheel mark shall be affixed visibly, legibly and indelibly to the product or to its data plate and, where relevant, embedded in its software. Where that is not possible or not warranted on account of the nature of the product, it shall be affixed to the packaging and to the accompanying documents. • The wheel mark shall be affixed at the end of the production phase. • The wheel mark shall be followed by the identification number of the notified body, where that body is involved in the production control phase, and by the year in which the mark is affixed. • The identification number of the notified body shall be affixed by the body itself or, under its instructions, by the manufacturer or the manufacturer's authorised representative. For specific products, manufacturers may use an appropriate and reliable form of electronic tag instead of, or in addition to, the wheel mark. Each unit of equipment normally to be installed in a distance of 5 m or less from a standard or a steering magnetic compass shall be clearly marked with the minimum safe distance at which it may be mounted from such compasses. Only for fixed equipment: Alternatively, the minimum safe distance may be given in the equipment manual. END OF CERTIFICATE Form code: MED 201.DEU Revision: 2016-12 www.dnvgl.com Page 2 of 2