2020.11.30 PDF HLD-INS600 GNV-GL型式认可证书 文件下载.pdf

Certificate No: MEDB000023U EC-TYPE EXAMINATION CERTIFICATE (MODULE B) Application of: Directive 2014/90/EU of 23 July 2014 on marine equipment (MED). This Certificate is issued by DNV GL SE based on the notification of the Federal Maritime and Hydrographic Agency of Germany. This is to certify: That the Integrated navigation system (INS) ND ER with type designation(s) HLD-INS 600 Issued to Beijing Highlander Digital Technology Co., LTD Beijing, China is found to comply with the requirements in the following Regulations/Standards: Regulation (EU) 2017/306, item No. MED/4.58. SOLAS 74 as amended, Regulations V/15, V/18, V/19 & X/3, IMO Res. A.694(17), IMO Res. MSC.36(63), IMO Res. MSC.97(73), IMO Res. MSC.191(79), IMO Res. MSC.252(83), IMO Res. MSC.302(87) LA Manufacturers authorised representative Rockson Automation GmbH Kiel, Germany Further details of the equipment and conditions for certification are given overleaf. GH This Certificate is valid until 2022-06-21. Issued at Hamburg on 2017-06-22 for DNV GL SE DNV GL local station: Tianjin HI Approval Engineer: Harald Bluhm Digitally Signed By: Mydlak-Röder, Christine Location: DNV GL Hamburg, Germany , on behalf of Notified Body No.: 0098 Sven Dudszus Head of Notified Body The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer’s Declaration of Conformity issued when the production-surveillance module (D, E or F) of Annex B of the MED is fully complied with and controlled by a written inspection agreement with a Notified Body. The product liability rests with the manufacturer or his representative in accordance with Directive 2014/90/EU. This certificate is valid for equipment, which is conform to the approved type. The manufacturer shall inform DNV GL SE of any changes to the approved equipment. This certificate remains valid unless suspended, withdrawn, recalled or cancelled. Should the specified regulations or standards be amended during the validity of this certificate, the product is to be re-approved before being placed on board a vessel to which the amended regulations or standards apply. Form code: MED 201.DEU Revision: 2016-12 www.dnvgl.com Page 1 of 3 © DNV GL 2014. DNV GL and the Horizon Graphic are trademarks of DNV GL AS. Job Id: 344.1-006438-2 Certificate No: MEDB000023U Product description 1. Product Type: HLD-INS 600 Comprising of: 2. Main Control Unit (Computer): HLD-MCU 200, or HLD-MCU 600 Software: Windows7 Operating System 4. Power Conversion Unit: HLD-PCU600 5. Human Interface Unit: HLD-IU600 6. Lan Switch: HLD-LS600 7. Signal Convert Unit: HLD-SCU600 ND ER 3. Display Units: Monitor TFT 24”, Type: HLD-DU134, or, HLD-DU140, or, HLD-DU150 Monitor TFT 26”, Type: HLD-DU135, or, HLD-DU141, or, HLD-DU151 LA Additional equipment: 8. UPS UPS (SURT1000 XLIM) Type: PC SMART-UPS RT 1000VA 230V UPS (SURTD2200 XLIM) Type: APC SMART-UPS RT 2200VA 230V EMC Filter (SURT023M) Type: SURT023M-APC 3000VA FILTER HI GH Manuals: HLD-INS 600 USER MANUAL HLD5100YH Rev 2.0 HLD-INS 600 INSTALLATION MANUAL HLD5100AZ Rev 1.1 HLD-INS 600 SERVICE MANUAL HLD5100FW Rev 1.0 HLD-ECDIS 600 OPERATION MANUAL HLD3400CZ Rev 1.0 HLD-ECDIS 600 INSTALLATION MANUAL HLD3400AZ Rev 1.0 HLD-RADAR 900 OPERATION MANUAL HLD1800Rev Rev 1.1 HLD-RADAR 900 INSTALLATION MANUAL HLD1800AZ Rev 1.0 HLD-TCS 600 OPERATION MANUAL HLD0800CZ Rev 1.0 HLD-SC 600 OPERATION MANUAL HLD0700CZ, Rev.1.0 Type Examination documentation 9065-16-39255-61924 – INS IEC 61924 Edition 1.0, 60945 test report-SIPAI – A15-006-ZC, 9065-16-39255_Network, 9065-16-39266-61162. Tests carried out IEC 60945 (2002) incl. IEC 60945 Corr. 1 (2008), IEC 61162 series: IEC 61162-1 ed5.0 (2016-08), IEC 61162-2 ed1.0 (1998-09), IEC 61162-450 ed1.0 (2011-06), IEC 61924-2 (2012), IEC 62288 Ed. 2.0 (2014-07). Marking of product According to Article 10 of the Council Directive (MED): - The wheel mark shall be affixed visibly, legibly and indelibly to the product or to its data plate and, where relevant, embedded in its software. Where that is not possible or not warranted on account of the nature of the product, it shall be affixed to the packaging and to the accompanying documents. Form code: MED 201.DEU Revision: 2016-12 www.dnvgl.com Page 2 of 3 Job Id: 344.1-006438-2 Certificate No: MEDB000023U - The wheel mark shall be affixed at the end of the production phase. The wheel mark shall be followed by the identification number of the notified body, where that body is involved in the production control phase, and by the year in which the mark is affixed. The identification number of the notified body shall be affixed by the body itself or, under its instructions, by the manufacturer or the manufacturer's authorised representative. HI GH LA ND ER For specific products, manufacturers may use an appropriate and reliable form of electronic tag instead of, or in addition to, the wheel mark. Form code: MED 201.DEU Revision: 2016-12 www.dnvgl.com Page 3 of 3